I’ll never forget the time my hoverboard got wet. I was riding through a puddle and didn’t realize how deep it was until it was too late. My hoverboard shorted out and stopped working. I thought for sure it was ruined, but I decided to try and fix it myself.
I followed the steps below and was able to get my hoverboard working again. It took a lot of work, but it was worth it in the end. If you find yourself in a similar situation, don’t give up – you may be able to fix your hoverboard, too!
Can hoverboards get wet or Are They Waterproof?
The answer to this question is a bit complicated. Technically, hoverboards are designed to be resistant to water and can therefore handle being in wet conditions. However, there are a few things to keep in mind if you’re planning on using your hoverboard in the rain or near water.
First, avoid riding your hoverboard in puddles or puddles of water – doing so could damage the hoverboard’s sensors. Second, if your hoverboard does get wet, make sure to dry it off as soon as possible to prevent any long-term damage. Finally, keep in mind that while hoverboards are designed to be resistant to water, they are not waterproof – so don’t ride them in the rain or through deep puddles!
Hover Board Electronics Don’t Like Water
The main reason you shouldn’t ride your hoverboard in the rain is that the electronics don’t react well to being wet. While the boards themselves are designed to resist water, the same can’t be said for the hoverboard’s electronic components.
These components are what make your hoverboard move, turn, and stop, so it’s important to keep them dry and free from water damage. If any of these components do get wet, it’s important to dry them off as soon as possible to prevent any long-term damage.
Another reason to avoid riding your hoverboard in the rain is that puddles can actually damage the hoverboard’s sensors. These sensors are located on the bottom of the hoverboard and help it to stay balanced and stable. However, they are also very sensitive and can be easily damaged by water.
If you do ride your hoverboard through a puddle or puddle of water, it’s important to dry off the sensors as soon as possible to prevent any damage. Additionally, try to avoid riding through deep puddles, as this could cause water to enter the hoverboard’s battery compartment and damage the hoverboard’s battery.
Pay Attention to the Motherboard
The motherboard is the hoverboard’s main control center and is responsible for controlling all of the hoverboard’s electronic components. The motherboard is populated with a variety of electronic components, including sensors, memory chips, and processors.
These components work together to control the hoverboard’s movements and keep it stable. The sensors are especially important, as they help the hoverboard know when to stop and turn.
However, the sensors are also very sensitive to water. If the sensors get wet, they can short circuit and cause the hoverboard to malfunction. As a result, it is important to keep the sensors dry and free from any moisture. Like the hoverboard’s sensors, the motherboard is sensitive to water and can be easily damaged if it gets wet.
Wet Hoverboard Battery = Bad News
As any hoverboarder knows, the battery is one of the most important components on the board. It is responsible for powering the motors that make the hoverboard move. However, the hoverboard battery is also very sensitive to water and can be easily damaged if it gets wet. For this reason, it is important to take measures to protect the hoverboard battery from water damage.
One way to do this is to keep the hoverboard in a dry location when it is not in use. If the hoverboard does get wet, it is important to dry it off as soon as possible and avoid using it until the battery has had time to dry completely. By taking these simple steps, you can help prolong the life of your hoverboard’s battery and keep your board running smoothly.
Warranties Don’t Like Water
Most hoverboard manufacturer’s warranties don’t cover water damage, so if you do ride your hoverboard in the rain or through a puddle and it ends up getting damaged, you may have to pay for the repairs yourself.
Keep this in mind when deciding whether or not to ride your hoverboard in wet weather conditions. It’s also important to make sure that you’re familiar with your hoverboard’s controls before riding it in any type of weather condition, as this can help you avoid accidents.
What to do if your hoverboard got wet?
Turn it off
If you get your hoverboard wet, the first thing you should do is turn it off. The longer you keep the board powered on, the higher the risk of damaging the internal components. Turning off the board will prevent shorts from occurring. Once the board is turned off, remove the battery. Next, dry off all of the components with a towel or cloth.
If possible, use a hairdryer on low heat to speed up the drying process. Once everything is dry, reassemble the hoverboard and test it to see if it’s still working properly. If the hoverboard doesn’t power on or if it seems damaged in any way, then it’s best to take it to a professional for repairs.
Dismantle it
Before you start dismantling your hoverboard, it’s important to take a few safety precautions. Make sure that the board is completely turned off and the battery unplugged. Once you’ve done this, you’re ready to start removing the screws that hold the bottom shell in place. In most cases, you’ll only need to remove the bottom covers to access the electronic components inside.
However, we recommend removing both bottom shells to ensure you locate all of the water that made its way into the board. With the bottom shells removed, you should be able to easily locate and remove any water that has pooled inside the board.
Unplug the battery
While it may seem like common sense, it’s important to remember to disconnect the battery from your hoverboard whenever it’s not in use. Even when the hoverboard is powered off, the battery can pose a safety hazard if it comes into contact with water.
By unscrewing the screws that hold the battery in place and unplugging it from the rest of the internal electronics, you can help avoid any potential accidents. While it may take an extra minute or two, it’s always better to be safe than sorry.
Locate water
If your hoverboard has gotten wet, it’s important to take some time to figure out where the water is located inside the board. Water can cause serious damage to the sensitive electronic components inside a hoverboard, so it’s essential to get rid of it as quickly as possible.
Fortunately, it’s usually pretty easy to spot where the water is. Look for water droplets or small puddles of water on the surface of the board. Once you’ve located the source of the leak, you can take steps to dry out the board and prevent further damage.
“Rice method”
One way to dry the wet part is to put them into a bowl of rice. The rice will help to absorb the moisture and prevent any rusting or corrosion. Keep the parts in the rice for 12 to 24 hours, and then dry them off before putting them back into the hoverboard.
You may also want to put the battery into the rice if it got wet, as this can help to prevent any permanent damage.
Cleaning parts
If you’re hoverboarding through a puddle and notice your wheels start to accumulate debris, make sure to stop and clean them off as soon as possible. If you don’t, the debris will continue to build up and can cause long-term damage to your hoverboard. The best way to clean your hoverboard’s wheels is to wet some Q-Tips with rubbing alcohol and gently scrub the affected areas.
Once you’re done scrubbing, make sure the areas are completely dry before you start hoverboarding again. This may seem like a lot of work, but it’s necessary to keep your hoverboard in good condition.
Reassemble and Power on
After everything has completely dried and been cleaned, it’s time to reassemble your hoverboard once again. Place the bottom shells in their original locations and re-screw them on with your screwdriver. If you took out the battery, make sure you reconnect it and put it back in its proper location.
It’s time to turn your hoverboard on and see if your hard work paid off after it was ruined. If your board powers up and operates properly, you’re ready to ride!
Hoverboard Water Damage
Water damage is a common issue for hoverboards as it can be difficult to take certain components apart, or even identify where a leak is coming from.
It’s important to understand the danger of water penetrating and corroding the sensitive internals of your hoverboard, as it can end up costing you expensive repairs.
To help prevent water damage, ensure that your hoverboard is stored in a dry place and every few weeks give it a quick check-up to make sure there are no signs of any possible leaks.
Any exposure to water can damage its internal circuitry and potentially ruin it completely removing all the fun you had with it. To prevent this from happening, be sure to always keep your hoverboard away from any water sources.
Water can affect the battery and its lifespan as well as cause other malfunctions that can alter the performance of your hoverboard. To be on the safe side, store your ride during wet or foggy weather
To Sum it up
There are a few things you can do to avoid hoverboards getting wet in the first place. First, try to avoid riding in wet or humid conditions if possible. If you must ride in these conditions, try to stay on dry surfaces as much as possible. Second, if your hoverboard does get wet, make sure to dry it off as soon as possible. By following these simple tips, you can help keep your hoverboard in good condition and avoid any water-related damage.
