What to Do If Your Jetson Hoverboard Won’t Turn On

If your Jetson hoverboard won’t turn on, there might be several issues causing this. In this blog post, we will outline some of the most common reasons why a Jetson hoverboard might not be turning on, as well as how to fix it.

Jetson Hoverboards are the perfect way to experience the revolutionary freedom of movement! From their inception in 2012, Jetson’s Hoverboards have been designed to provide the safest, most enjoyable ride out there. Their engineers understand that a great ride is not just about speed and agility; it should also foster confidence, safety and fun.

Jetson Hoverboard Won’t Turn on

If your hoverboard isn’t turning on when you press the power button, there are a few possible culprits.

• First, and easiest to check, is to make sure that it is properly connected to its charger – if it’s not plugged in or is not charging correctly, then that may be your problem right there.
• Second, you’ll want to look into any battery issues: if it hasn’t been charged recently or has lost its charge quickly, the battery could be on its way out.
• Thirdly and more complexly, a wiring issue could be at hand; hoverboards involve lots of intricate electrical components that need to be placed just right. For this one, you may want to reach out to an expert who can find where any problems lie within the wiring.
• Finally, both hardware and software problems can occur when there’s a motherboard issue – this means something has gone wrong inside the hoverboard itself.

In some cases, a manufacturer’s defect may be your underlying cause here as well.

Charger Problems

With most batteries, if they don’t charge right away, it could mean that the charger isn’t working.

Before you take your hoverboard to a repair shop, be sure to inspect the charger itself by looking for any signs of damage or lose connections. If the charger looks intact and still isn’t working properly, try swapping in a replacement charger to see if that makes a difference.

Checking your charger for potential problems is simple. Connect your charger to the wall, then to the hoverboard itself. You should see a green indicator light at first – this usually lasts up to a few minutes.

If it doesn’t turn red before turning green again, this might mean your charger is defective and needs replacing. To confirm this diagnosis, you can try another charger (as long as it’s from the same manufacturer).

If this new charger does turn red briefly before returning to green, then the problem isn’t with the charger – it is likely with the board itself or its battery. Replacing these components may resolve the issue.

Wrong Charging Method

If you’re having trouble getting your Jetson up and running, you should first make sure the charger is connected to the wall and that the green indicator light is turned on.

Additionally, you’ll want to check that the power button on the side of the power box or battery pack is in the OFF position before plugging it into the charger.

If this isn’t done correctly and you’ve mistakenly been charging with the board turned on, don’t fret! Let your device rest for 24-48 hours before attempting to charge it again.

Once plugged back into the charger, it should change from red to green in about fifteen minutes if connected properly.

Defective Charger

Chances are your hoverboard is not turning on because of a slow or defective charger. The best way to avoid this issue is by sticking with the charger the hoverboard came with – no generic ones here.

If you get a chance – try to connect a different charger to the hoverboard.

Charging Port Problems

If your hoverboard’s charging port seems to be having issues, there is probably an easy fix. All you have to do is take a look at the charge port: it will have three pins and likely an accompanying little plastic plug where you can spot the locator tab.

When inserting the charger, make sure that the slot of the cord lines up with the tab to start charging. If the charger light turns red and stays red, it indicates that your board is now being charged correctly.

Battery Issues

It’s easy to take a quick look at the battery to see if there might be an issue.

First, make sure your charger and hoverboard are connected, then turn on the board – if it starts flashing orange on the battery indicator, it’s time for a replacement – don’t fear though, batteries are relatively inexpensive and easily replaceable.

If the fully-charged battery doesn’t have enough volts after checking with a voltmeter, then it too needs replacing.

Dead Battery

If you’re having trouble charging your hoverboard or getting it to turn on, you may be dealing with a depleted battery.

This issue comes from the battery management system (BMS) detecting too much amperage during a charge and cutting off the power. To make sure this is what’s going on, it’s helpful to use a voltage meter on the end of the battery’s terminal.

If it reads less than 36 volts (normally about 33-34 volts), then your battery is probably too low to charge unassisted.

On the other hand, if it reads more than 40 volts, there may be an error with the BMS system itself. To do this quick check-up, you’ll need to carefully remove the battery from your hoverboard.

Wiring Issues

If you think it’s not your charger or battery causing the problems, the next step is to take a close look at the wiring. Open up your board, and inspect each wire for any frays or damage.

Make sure all wires are secure and tightly plugged in, especially in the charger port area. A good idea is to remove the port connector and plug it back in; this can sometimes fix a wide range of issues.

Defective Motherboard

Unfortunately, there’s no easy way to know for sure if this is the cause. Replacements are generally available from any reputable hoverboard company, so you don’t need to discard your entire board.

If this is what you’re dealing with, the best course of action is to get in touch with your manufacturer.

Defective Hoverboard

If nothing else you’ve tried has resolved the issue, it’s possible that your board is defective. Don’t worry though, there are still steps you can take to either get a refund or part of one.

The first thing to do is look into the model online – sometimes recalls happen and faulty parts are involved. If not, then contact the company directly and speak with customer service.

It might result in a full or partial refund or replacement.

Common Causes of a Jetson Hoverboard Not Working

Here is a table that lists the common causes of a Jetson hoverboard not turning on, along with their corresponding troubleshooting solutions:

Problem Type	Causes	Troubleshooting Solutions
Battery	Low battery level or loose connections	Check the battery level and make sure the connections are secure. Charge the battery for at least 2 hours before trying to turn on the hoverboard again.
Power switch	Power switch is not in the “on” position	Ensure that the power switch is in the “on” position.
Fuses	Blown fuses	Check the fuses and replace them as necessary.
Circuit board	Circuit board is not working properly	If the above solutions don’t work, the problem may be with the circuit board. In this case, it’s best to take it to a professional for further diagnosis and repair.
Charger	Charger is not working properly	Check the charger and make sure it’s working properly. If it’s not, the charger might be faulty and needs replacement.
Motor	Motor is not working properly	Check the motors, see if they are making any noise or not. If they aren’t, the motors might be faulty and needs replacement.

FAQ